Visual Inspection Details

AAIS Procedure for Visual Testing - AAIS-NDT-VT-1-R1

This document identifies the requirements to conduct Visual Test on new and in-service assets such as, Process Piping, Equipment, Steel Structures and piping systems in compliance with the approved international codes and standard referenced here, considering all HSE requirements.

AAIS

Free

1,134 KB

ASME B 31.3 96 TABLE 341.3.2 ACC. Criteria For Visual Test

This paper covers the visual testing acceptance criteria as per mentioned in API 1104, API 650 & ASME B31.3

N/A

Free

22 KB

ASME sec V Non-Destructive Examination

This Section of the Code contains requirements and methods for nondestructive examination (NDE), which are Code requirements to the extent they are specifically referenced and required by other Code Sections or referencing documents

ASME

Upon Request

10,753 KB

ASNT - Boiler Tubes - Comparison Of Visual, Eddy Current, Ultrasonic, Magnetic Particle Testing Techniques

This paper details actual inspection data and extracts from reportstaken over a nine-month period of inspections of water tube boilers.The inspections were carried out by qualified technicians andinspectors using a combination of internal visual testing (VT) usingremote cameras, eddy current testing, ultrasonic testing (UT) and magneticparticle testing (MT).

Michael Leonard Hodgson

Upon Request

3,124 KB

ASNT - Nondestructive Testing Handbook - Vol.8 - Visual and Optical Testing

Visual and Optical Testing, the eighth volume in the second edition of the Nondestructive Testing Handbook series, demonstrates again AS NT's dedication to its missions of providing technical information and instructional materials and promoting nondestructive testing (NDT) technology' as a profession.

ASNT

Upon Request

18,144 KB

ASNT - Nondestructive Testing Handbook - Vol.9 - Visual Testing

The authoritative reference for visual inspection. Emphasis on practicality, with information for Level II and Level III inspectors. Applications including metals, welding, chemical, petroleum, electric power, aerospace. Scores of illustrations of anomalies. Diverse information in one place. Updated standards. Digital photography and video. Image processing. New and authoritative discussion on vision acuity. Metric units throughout. Updated references provided for published standards.

ASNT

Upon Request

7,307 KB

ASNT - Relevant Discontinuities - Visual Inspection

includes overviews of each discontinuity, with descriptions, locations in the test part, and characteristics. It features more than 30 inherent, processing, and in-service discontinuities detectable by visual testing,

ASNT

Upon Request

1,608 KB

ASNT Level II Study Guide - Visual And Optical Testing Method

This study guide contains basic information intended to prepare a candidate for Level II visual and optical testing examinations administered within the ASNT Central Certification Program (ACCP). This study guide does not present all of the knowledge necessary for certification; the candidate is expected to supplement this guide with the recommended references that follow.

ASNT

Upon Request

1,979 KB

ASNT Level III Study Guide - Visual And Optical Testing Method

ASNT study guides provide prospective ASNT Level III examinees with enough technical knowledge to pass an ASNT NDT Level III examinations. Intended to be used with a comprehensive NDT text, such as volumes from the Nondestructive Testing Handbook series.

ASNT

Upon Request

3,804 KB

AWS - PHB-6-The Everyday Pocket Handbook for Visual Inspection of AWS D1.1

The inspection requirements for the fabrication and welding of steel structures are very extensive. This Pocket Handbook has been developed to provide a useful tool for inspectors to carry in their pockets or tool kits so that selected pertinent portions of the AWS Structural Welding Code—Steel, D1.1/D1.1M:2004, can be easily referenced at the job site.

AWS

Upon Request

735 KB

AWS-The Practical Reference Guide For Welding Inspection Management-VT of Pressure Vessels And Pressure Piping

Visual inspection (VT) is one of the more important inspection methods used to ensure the quality of both new fabrication, as well as equipment and piping after some period of service. It is used in all industries, and should be considered as the basic inspection method prior to the selection of any other inspection method.

AWS

Upon Request

1,032 KB

AWS B1.10 - Guide for The Nondestructive Examination of Welds

This standard provides a reference guide for the kinds of nondestructive exmination methods that are used to verify that welds meet requirements of a code or specification.

AWS

Upon Request

154 KB

AWS B1.11 - Guide for the visual Inspection of welds

This guide includes an outline of the fundamental prerequisites for personnel performing visual examination of welds. Such prerequisites include physical limitations or capabilities, as well as technical lnowledge, training, experience, judgement, and certification.

AWS

Upon Request

1,891 KB

AWS VIW-M 2008-4th Ed. Visual Inspection Workshop-Reference Manual

This manual essentially provides an introduction to visual examination of welding. These examinations fall into three categories based on the time they are performed, as follows: (1) prior to welding, (2) during welding, and (3) after welding. An extensive treatment is provided on weld surface conditions, including reference to frequently used terminologies associated with preferred and nonpreferred conditions. Visual examination may be performed by different people or organizations.

AWS

Upon Request

2,168 KB

BS EN ISO 17637 - Non-destructive Testing Of Welds - Visual Testing Of Fusion-Welded Joints

This International Standard covers the visual testing of fusion welds in metallic materials. It may also be applied to visual testing of the joint prior to welding.

BSI

Upon Request

276 KB

BS EN13927 - Non-Destructive Testing - Vesual Testing - Equipment

This European Standard describes general requirements for equipment used in visual testing. The application of equipment is necessary in visual testing when: Objects, which are visually or on account of environmental factors not accessible. - Need to be made accessible to viewing. - The test sensitivity is insufficient. - An imaging record is required. This European Standard includes the verification of equipment.

BSI

Upon Request

42 KB

CBI Module 16 - Techniques of Visual Inspection

The objectives of this module, therefore, are to discuss a wide range of techniques in the inspection of welds and welded products and to cover what is traditionally termed visual inspection.

CWB

Upon Request

2,254 KB

Defects And Discontinuities

This presentation covers and describes the basics and definitions of defects and discontinuities.

Tim Turner

Free

299 KB

Guide To Weld Inspection For Stractural Steelwork

This guide is complementary to the BCSA’s National Structral Steelwork Specification for Building Construction 5th edition CE Marking Version on (NSSS) which states that “it can be used for all types of building construction designed for static loading. It is based on execution of structural steelwork in Execution Class 2 according to BS EN 1090-2.

BCSA

Upon Request

233 KB

ISO 17637 - Non-destructive testing of welds - Visual testing of fusion-welded joints - Second Edition

This document specifies the visual testing of fusion welds in metallic materials. It may also be applied to visual testing of the joint prior to welding.

ISO

Upon Request

135 KB

Remote Visual Inspection Basics

This paper covers and describes the remote Visual Inspection and its featuees and applications.

GRANT REIG

Free

152 KB

The Every day Pocket Handbook For Visual Inspection and Weld Discontinuities - Causes and Remedles

This book Covers the following: (Basic Safety precautions, Visual Inspection Notes, Discontinuities types, Fillet weld measurement, Metric Conversion Table, Plate and pipe dimentions, NDT symbols

AWS

Upon Request

48 KB

The Everyday Pocket Handbook For Visual Inspection Of AWS D1.1 Stractural Welding Code's, Fabrication & Welding Requirements

This Pocket Handbook has been developed to provide a useful tool for inspectors to carry in their pockets or tool kits so that selected pertinent portions of the AWS Structural Welding Code—Steel, D1.1/D1.1M:2004, can be easily referenced at the job site.

AWS

Upon Request

90 KB

Visual Testing Measuring Tools

This file covers and describes the tools used in Visual inspection and what it used for.

N/A

Free

470 KB